Solar Multi-Purpose Intelligent Car Sunshade Umbrella

C-01
1. Functional description
·After installing this product, the sun protection effect is obvious, and the cooling effect in the car is significant (the temperature is reduced by nearly half).
·Non-destructive installation, no need to charge for normal use, and charging is required once if not used for more than three consecutive months.
·Relieve the damage to the human body caused by the concentrated release of carcinogens such as formaldehyde in the car due to exposure or high temperature.
·Effectively prevent the spontaneous combustion of flammable materials in the car caused by exposure or high temperature.
·Effectively alleviate the premature aging of the center console and interior due to exposure, making the vehicle newer over time and increasing the residual value of the vehicle.
·Relieve the damage of falling objects from high altitude to the car and the vehicle
2. Functional features
·One machine with three uses: car sunshade + outdoor canopy (optional) + camping tent (optional), 3 scenes can be quickly switched.
·Solar charging: photovoltaic power generation, smart charging, green and energy-saving.
·Super strong sun protection: physical isolation sunscreen coating, even in the midday sun, the car is still comfortable and cool.
·Simple control: one-button start and stop - smooth response, natural contraction.
·Anti-theft device: autonomous anti-theft design, worry-free travel.
·Wind-resistant design: all-aluminum body, wind resistance can reach level 5 when unfolded.

Solar multi-purpose smart car-mounted sunshade with three uses in one device

Usage scenario

Car sunshade

Outdoor canopy (optional)

Camping tent (optional)

Scene display

 

 

 

Scene accessories

Host, foot

Host, foot, bracket

Host, foot stand, bracket, tent

3. Operation Instructions
· Power on: Press and hold the power button ON for 3 seconds to turn on the main unit.
· Power off: When powered on, it will automatically shut down after 5 seconds.
· Umbrella expansion: When powered on, press and hold the power button ON for 2 seconds until a beep is heard, then release the button and the umbrella will automatically open.
· Umbrella folding: When powered on, press and hold the power button OFF for 2 seconds until a beep is heard, then release the button and the umbrella will automatically fold.


4. Installation Instructions


① Place the gripping foot in the middle of the roof (use the front gap or rear gap of the B-pillar as the reference line, and align the gripping feet on both sides to ensure they are in the same straight line).

②Use a hexagonal wrench to tighten the two screws at the bottom of the gripping foot. Note: Do not tighten the screws. Fix the gripping foot on both sides of the vehicle's crossbar.

③Place the parasol main unit over the gripping feet, making sure the parasol main unit is in the middle of the roof.

④Slide the connection base under the main unit over the gripping feet, aligning the screw holes and keeping them on the same level.

⑤ Determine the host connection base position, and confirm the host position again. ⑥ After fixing the host connection base position, remove the host, install it in the middle of the top of the car, and tighten the host connection base screws.

⑥After fixing the host connection seat, remove the host and install the rubber strip at the bottom of the host.

⑦Fill the gaps in the base slider with the rubber strip (Note: Cut the rubber strip accurately to avoid gaps that cause howling).

⑧After the rubber strips are installed, place the main unit on top of the roof grip feet to install the main unit.

⑨Tighten the screws above the main unit connection base and the gripping foot, and tighten the screws below the gripping foot again.

⑩Check and tighten all screws to ensure they are in a tight state. After checking and confirming that they are correct, the installation is complete. The user needs to check the status of all screws from time to time. If any screws are loose, tighten them in time.
5.Key points for installation:
1. When fixing the gripping feet on the roof, make sure that the gripping feet on both sides are aligned, and do not tighten the screws under the gripping feet too much. Tighten them after the installation is completed.
2. When determining the position of the host connector, you can use measuring tools such as a tape measure to ensure that the host is located in the middle of the top of the car. After determining the position of the connector, lock the connector position.
3. When installing the rubber strip at the bottom of the host, use a tape measure to first measure the gap spacing of each section of the slider at the bottom of the host, and then cut the rubber strip to fill the slider gap as much as possible.
6. Precautions
·This product is mainly used for cooling and sunshading of vehicles. It is not recommended to use this product in strong winds (level 5 or above) and rainy and snowy weather.
·The sunshade function is prohibited during driving.
·The installation screws must be checked from time to time to see if they are loose, and the screws must be tightened in time. Special attention: Before getting on the highway, it is necessary to check whether the installation screws are loose.
·This product has achieved non-destructive installation, but it must be handled with care during installation and not to scratch the vehicle body.
·When it is not used for a long time in autumn and winter, it is recommended to remove this product from the vehicle (not recommended when the canopy and tent are selected).
·If the battery is exhausted after repeated use in the absence of light for a long time, the host can be placed under the sun or charged with a mobile power bank to activate the battery. After ten minutes, connect the charging cable to the USB port in the car for charging.
·To avoid circuit failure, do not press the power button and the power button at the same time.
·Special statement: Customers who have selected outdoor canopies and camping tents should pay attention to avoid hard objects squeezing the solar panels when installing the outdoor canopy to avoid damaging the solar charging panels.

Name

Solar powered multi-purpose smart car sunshade

Color

  □ silver                 □ black

Style

□ Sedan          

□ SUV close-fitting

□ SUV Suspension Model

Weight

21kg

21kg

21kg

Dimensions

Main unit size: length 1480cm width 214cm height 138cm

Unfolded umbrella size: length 2980cm width 1480cm

Outer packaging size: length 158cm     width 37cm   height 21.5cm

Material

Aluminum alloy + stainless steel + yarn-dyed fabric

Battery

Battery capacity: 1100mAh (folding ≥23 times when fully charged),

Charging time: 1 hour

Charging

Type-C interface: Car charging: 5V 2A, working voltage: 12V, cable length: 2m

Solar charging: 13V 1A

Certification No.

W-1047-23CNL

Implementation Standard

GB/T19951-2019    GB/T21437.2-2008

Product No.

See the main body

Get the latest price? We will respond as soon as possible (within 12 hours)
captcha